![artec studio global registration artec studio global registration](http://docs.artec-group.com/as/13/en/_images/5_Auto_Post_Processing_alternative.png)
- #Artec studio global registration how to
- #Artec studio global registration registration
- #Artec studio global registration software
#Artec studio global registration registration
Global Registration: After I’ve cleaned up the capture, I like to another registration to ensure all frames are properly lined up.įusion: This step is where the real action takes place. I used only a very few of them, and I can see how they would be useful for more complex projects.
![artec studio global registration artec studio global registration](https://www.cadcam.org/wp-content/uploads/2018/11/artec-eva-en.png)
Artec Studio has a large number of editing tools to do practically anything you can imagine on the capture. If you haven’t automatically removed the floor, this is where you do that. Generally, however, the workflow I went through was something like this:Įditing a 3D scan capture in Artec Studio Įditing: Once the capture makes more sense, this is the step I take to remove clutter and surfaces that are not required.
#Artec studio global registration software
Once the scan is loaded into Artec Studio, there are many ways to proceed, as the software is quite flexible. While it’s not an instant transfer, I never waited very long for transfers to complete. The scans are of considerable size, because they are comprised of a mix of scan and texture images. It’s a straightforward method that’s easy to trigger.Īnd it’s also quite fast.
![artec studio global registration artec studio global registration](http://printmakersopenforum.org/yahoo_site_admin/assets/images/Sue_Carrie_Drummond.117125302_std.jpg)
There are a couple of ways of doing so, but the recommended approach is to use a standard Ethernet cable between scanner and laptop. The first step in processing is to transfer the scan from the handheld unit to the laptop. Even better, there are ways to join separate scans of the same object together. The Artec Leo operates so swiftly it’s not that much trouble to get another scan while you’re set up on site, and it could save a lot of trouble afterwards. If you missed something, then it would be a good idea to have another scan in your pocket. It might be a good idea to capture objects more than once in the field, especially if you are not processing them on site. You’ll be using Artec Studio, a powerful tool. This is usually done back at a desk, where you can let the machine run for longer periods. Artec Leo Capture ProcessingĪrtec Studio ready to process a 3D scan Īfter all the fun of capturing objects, the less exciting job of processing the data takes place. Well, perhaps they may have finished eventually, but processing was certainly too long to be practical. I attempted to do several HD captures, and while I captured objects, I was unable to process them on the provided laptop, an HP ZBook 15,, 64GB, Quadro M 1000M. However, there’s a caveat: you must have a powerful laptop on the other end to process it.
![artec studio global registration artec studio global registration](https://europac3d.com/wp-content/uploads/2018/09/as13-banner.jpg)
If you tick this box, then that data is captured. HD Recording: This is a special feature that allows far greater detail in the capture. I like that mode because then my job as the operator is to simply slide that sweet green zone over top of all surfaces. Distance will give you a “red or green” depending on your optimal distance from the subject.
#Artec studio global registration how to
Overlay or Distance: This is an interesting feature that tells the display how to operate during scanning. If you’re farther away, there is less detail in the capture. Typically it’s set to ensure you keep close enough to capture a sufficient amount of detail. Range: This value determines how far away the scanner’s range will be during this scan job. If you’re just capturing a geometry of a part, then it can be low. The choice depends on whether the texture is important. Texture Brightness: This tells the scanner how bright the captured texture should be. This is a bit of a shortcut as normally you’d clip off that segment during post-capture processing. Usually this means the floor or table on which the subject is positioned. There are several options that I will explain and you’ll get a better idea of how it operates.īase Removal: This feature tells the scanner to discard the “base”. Scan job setup screen on the Artec Leo handheld 3D scanner Ībove we can see the image on the Artec Leo 3D scanner when you are to start a new scan job.